Use fully charged battery or AC power while OS update process.
Every information or configurations will be removed after OS update if Format All is performed.
Check first whether the WLAN module type is Summit or Samsung. Wrong OS update may cause severe damage to device leading to RMA process.
OS Update via (Mini) SD Card
Required files for OS update can be downloaded from support webpage.
Formatting MiniSD - please format MiniSD card on PC in FAT (recommended) or FAT32 format.
Please copy OS image file (must in name FLASH.DIO), Boot image file (BOOT.NB0) and SPLASH.BMP to SD card and then insert it into the device.
Note that the SD Card for each device has different dimensions. SKY uses MiniSD and SD for MM3.
The device should be turned off first. The device power can be turned off by pressing the ‘Power button’ for 10 seconds.
Press the right arrow button and keep pressing. Press the power button briefly to enter Boot menu.
Select [1. Update] Press return button.
Select [1. SD Update] > [2. BOOT Update]
Turn off the device by pressing the power button for 10 seconds. Then re-enter the boot menu.
Select [2. Format All] and press return button.
'Format all partitions Confirm it' message will be displayed.
Select [1. Yes]
'Format completed Update boot and OS' message will be displayed.
Then, select [0. BACK] to enter Main MBoot MENU.
From the main boot menu, select [1. Update] -> [1. SD Update] -> [3. SPLASH Update].
SPLASH update will update the image that is displayed when booting.
To use your own image, you should have 240 x 320 pixel 24 bit bitmap file and save it as SPLASH.bmp.
After successful update, return to the update menu.
Select [2. BOOT Update] N.B. We strongly recommend updating BOOT prior to OS update. 'BOOT. NB0 Write done' message will be displayed.
Then, turn off the terminal again and re-enter the boot menu.
Select [1. Update] > [1. SD Update] > [1. OS Update] from the update menu.
'Writing done. Reset Device!!' message will be displayed.
Then, finish OS update by resetting the device.
[Format All] process will remove the previous Flash Disk files. To copy the flash disk files back to the PDA, you can either use SD card or ActiveSync (via USB).
OS Update via One-click Update
Required files for OS update can be downloaded from Support webpage.
Downloaded zip file will contain two folders: Oneclick_Update and SD_USB_Update.
To use one-click update, simply copy the mpk file to the flash disk of the PDA and run it.
Then, it will automatically update splash, boot and OS, and reset.
In the case where the mpk file is not available, you can make mpk file using MakeMPK.exe.
Run MakeMPK.exe on your PC and select correct OS image, boot and splash file. ※ Auto File Name Set is checked - When selected OS Image folder that has the Boot and Splash file, the folder path will be set automatically. And Target Folder will also automatically set the path.
Select the Target Folder and Insert the Target Name. And press the Start button, a new file will be created on the Target Folder path.
Please store the created file on the SD card and insert the SD card in the device. Please run the file (.MPK) to proceed. OS update.
OS Update via USB Downloader(32bit only)
I. Installation
Download the USB_Downloader and OS update files to your PC.
Copy the rndismpy.sys and usb8023y.sys files (in USB_Downloader-> USB drive) to on your PC in this path (Windows\System32\Drivers).
Turn off the device (The device power will be turned off by pressing the ‘Power button’ for ten seconds.)
Press the right arrow key then briefly press Power button. [MBOOT MENU] will be displayed.
Please select [Update] -> [TFTP Update] then select the requested updates.
On the screen ‘Waiting for USB connect…’ will be displayed.
Please connect the device to PC via USB cable.
Now the PC will detect NEW hardware.
For install driver you have to browse the Folder in USB_Downloader -> USB Driver. The driver is called ‘RNDIS_PXA270.inf’.
Turn off the device (The device power can be turned off by pressing the ‘Power button’ for ten seconds.).
Press the right arrow key together with Power button. [MBOOT MENU] will be displayed.
Please select Update -> TFTP Update then select the requested updates.
On the screen ‘Waiting for USB connect…’ will be displayed.
Please connect the device to PC via USB cable.
On your PC Network Connections -> MobileCompia Network -> Properties.
Internet Protocol (TCP/IP) -> Properties.
Set IP: 10.0.0.5 / Subnet Mask: 255.0.0.0
II. Upload OS
Run TFTPClientV1.4.exe in USB_Downloader.
Update OS in the order Splash -> Boot -> OS image.
The device should be turned off first. Press the right arrow button and keep pressing. Press the power button briefly. The [MBOOT MENU] will be displayed.
From boot menu, select [Update] -> [TFTP Update].
The upload is ready to proceed, when you see the message 'Update process is ready' on the TFTP Client.
When you see above message, press 'Start' to begin the upload process.
CAUTION - Do not power off the device or remove Ethernet cable during this process.
