Menu
Search
Search
Searching...
 
   
   
   
 
Search
 
← Previous page
 
Next page →
 

M3 SMART WM

CAUTION
  • Use fully charged battery or AC power while OS update process.
  • MicroSD memory size should be less than 2GB.
 
NOTE
  • When MicroSD card is used for OS update.
  • This manual assumes updating both BOOT and OS using IMAGES.BIN.
  • Please make sure your device type whether 2G or 3G type.
  • Ex) OS ver. : C3STH6150EN(‘H’ means HSPA, 3G type)
    Product No. : UA10HGDNKLxxxxx
  • Ex) OS ver. : C3STG6147EN(‘G’ means GSM, 2G type)
    Product No. : UA10GPDNLG41897
 

OS Update via MicroSD Card

 
  • To update the OS, user can choose update files to suit their requirements.
    BOOT.BIN
    used to update BOOT only
    FLASH.BIN
    used to update FLASH (OS) only
    IMAGES.BIN
    used to update BOOT and OS (Recommended)
    IPL.BIN
    used to update boot image (splash image)
    Copy IMAGES.BIN to root folder of MicroSD then, insert the micro SD card to the device.
  • Turn off the device by pressing the power button for approximately 10 seconds.
    Then, while pressing the right arrow button, press power button to enter the boot menu.
    [BOOT MENU 1.0.2]
    1) SD Download
    2) USB Download
    3) Clean Boot
    4) Factory Reset
    5) Device ID(UUID)
    6) Debug Serial:[NO]
    7) ALL Format
     
    Select Number
     
    0) Exit:Launch OS image
     
    SAMSUNG-S5PC100 833MHz
    RAM 256MB / ROM 1GB

     
  • From the boot menu, press ‘1’ to enter SD Update Mode. Then, press ‘3’ to start update.
    When OS update is completed, reset the device.
 
 

OS Update via USB Downloader(32bit only)

 
  • Download all necessary files to your PC.
  • OS file.
  • USB Update tool: M3SMART_USBDown.zip
  • USB Driver if necessary: M3SMART_Driver.zip
     
  • Turn off the device by pressing the power button for approximately 10 seconds.
    Then, while pressing the right arrow button, press power button to enter boot menu.
    [BOOT MENU 1.0.2]
    1) SD Download
    2) USB Download
    3) Clean Boot
    4) Factory Reset
    5) Device ID(UUID)
    6) Debug Serial:[NO]
    7) ALL Format
     
    Select Number
     
    0) Exit:Launch OS image
     
    SAMSUNG-S5PC100 833MHz
    RAM 256MB / ROM 1GB

     
  • From the boot menu, press ‘2’ to enter USB Download Mode. Then, press ‘1’ to prepare the PDA for USB OS update.
     
    [ USB Download Mode ]
     
     
     
     
     
    USB Download Ready..
    Please Send Image File
     
     
     
     
    0) Power Off
     
    When it displays USB Download Ready, connect the PDA to the PC.

     
  • Place M3 SMART on the cradle and connect to a PC via USB cable. ‘Found New Hardware’ message will be displayed on your PC and will automatically install required driver.

    If the driver is installed properly, please go to step 11, otherwise proceed to step 5.
     
  • If the driver is not installed properly, the driver must be installed manually.


    Please open Device Manager. (Control Panel > Hardware and Sound > Devices and Printers > Device Manager).

     
  • Double click on SEC S5PC100X Test B/D to open the properties and click on Update Driver…

     
  • Click on Browse my computer for driver software

     
  • Then, select the folder where the driver files are located by click on Browse…

     
  • When a warning window pops up, click on Install this driver software anyway.


    Then, it will start installing driver software.

     
  • Close the window after the driver installation is successfully done.

     
  • Launch USBDown.exe to start OS update.

     
  • Select ‘All Image’ and click on Open to select Images.bin, OS file.
     
  • When the correct OS file is selected, click start to proceed.

     
  • When OS update is complete, PDA will display complete message on the screen. Then press ‘0’ to launch OS image.
 
M3 MOBILE Co., Ltd.